Danfoss VLT 6000 Wartungshandbuch Seite 23
- Seite / 28
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
VLT
®
6000 HVAC
Programming
■ Changing data
Regardless of whether a parameter has been
selected under the Quick menu or the Extended
menu, the procedure for changing data is the same.
Pressing the [CHANGE DATA] key allows change
of the selected parameter, and the underlining
in line 4 will flash on the display.
The procedure for changing data depends on whether
the selected parameter represents a numerical
data value or a functional value.
If the chosen parameter represents a numeric data
value, the first digit can be changed by means of
the [+/-] keys. If the second digit is to be changed,
first move the cursor by using the [<>] keys, then
change the data value using the [+/-] keys.
175ZA698.10
24.2 Hz
SETUP
1
FREQUENCY
205 MAX. REFERENCE
000060,000 Hz
5
The selected digit is indicated by a flashing cursor.
The bottom display line gives the data value that will
be entered (saved) when signing off by pressing the
[OK] button. Use [CANCEL] to cancel the change.
If the selected parameter is a functional value,
the selected text value can be changed by
means of the [+/-] keys.
175ZA689.10
3.90 A
SETUP
1
210 REFERENCE TYPE
SUM
MOTOR CURRENT
The functional value flashes until signing off by pressing
the [OK] button. The functional value has now been
selected. Use [CANCEL] to cancel the change.
■ Infinitely variable change of numeric data value
If the chosen parameter represents a numeric data
value, a digit is first selected by means of the [<>] keys.
175ZA699.10
SETUP
1
50.0 Hz
FREQUENCY
209 JOG FREQUENCY
0
9 .0 Hz
SETUP
1
Then the chosen digit is changed infinitely by
means of the [+/-] keys:
175ZA700.10
SETUP
1
50.0
FREQUENCY
209 JOG FREQUENCY
1
0.0 Hz
SETUP
1
The chosen digit flashes. The bottom display
line shows the data value that will be entered
(saved) when signing off with [OK].
■ Changing of data value, step-by-step
Certain parameters can be changed both step by
step and infinitely variably. This applies to Motor
power (parameter 102), Motor voltage (parameter
103) and Motor frequency (parameter 104).
This means that the parameters are changed
both as a group of numeric data values and as
numeric data values infinitely variably.
■ Manual initialisation
Disconnect from mains and hold the [DISPLAY
MODE] + [CHANGE DATA] + [OK] keys down while
at the same time reconnecting the mains supply.
Release the keys; the frequency converter has now
been programmed for the factory setting.
The following parameters are not zeroed by means of man
ual
initialisation:
Parameter 500, Protocol
600, Operating hours
601, hours run
602, kW h counter
603, Number of power-ups
604, Number of overtemperatures
605, Number of overvoltages
It is also possible to carry out initialisation via
parameter 620 Operat ing mode.
MG.60.C8.02 - VLT is a registered Danfoss trademark
23
Verwandte Produkte und Handbücher für Netzteile und Wechselrichter Danfoss VLT 6000
(1 Seiten)
(2 Seiten)Rocktron VersaTune podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Audio Rocktron VersaTune.
Dostarczamy 1 pdf podręczników Rocktron VersaTune do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Kommentare zu diesen Handbüchern