Danfoss FC 100 Series Spezifikationen PDF herunterladen (Seite 64)

Two finger initialization:

1. Power off the frequency converter.

2. Press [OK] and [MENU].

3. Power up the frequency converter while still

pressing the keys above for 10 sec.

4. The frequency converter is now reset, except the

following parameters:

15-00 Operating Hours

15-03 Power Up's

15-04 Over Temp's

15-05 Over Volt's

15-4* Drive identification parameters

Initialisation of parameters is confirmed by AL80 in the

display after the power cycle.

How to Programme VLT HVAC Basic Drive Design Guide

MG.18.C2.02 - VLT

is a registered Danfoss trademark 63

1 2 ... 59 60 61 62 63 64 65 66 67 68 69 ... 92 93

Design Guide 1
MG.18.C2.02 - VLT 2
2 MG.18.C2.02 - VLT 3
Revision Rights 4
Basic Drive 4
1.1.4 Abbreviations 5
1.1.5 Definitions 6
6 MG.18.C2.02 - VLT 7
Power Factor 8
DANGEROUS VOLTAGE 9
UNINTENDED START 9
DISCHARGE TIME 9
IEC/EN 60068-2-6: 11
Vibration (sinusoidal) - 1970 11
10 MG.18.C2.02 - VLT 11
Comparison of Energy Savings 13
Without a Frequency Converter 15
Application Examples 16
2.5.12 Variable Air Volume 16
2.5.13 The VLT Solution 17
2.5.14 Constant Air Volume 18
2.5.15 The VLT Solution 18
2.5.16 Cooling Tower Fan 19
2.5.17 The VLT Solution 19
2.5.18 Condenser Pumps 20
2.5.19 The VLT Solution 20
2.5.20 Primary Pumps 21
2.5.21 The VLT Solution 22
2.5.22 Secondary Pumps 23
2.5.23 The VLT Solution 23
2.6 Control Structures 24
Feedback Conversion 25
2.6.5 Reference Handling 26
26 MG.18.C2.02 - VLT 27
28 MG.18.C2.02 - VLT 29
2.6.8 Manual PI Adjustment 31
2.7 General Aspects of EMC 31
2.7.2 Emission Requirements 32
2.7.3 EMC Test Results 33
Emission 34
= 3 × 120 × 400 × 35
175ZA052.12 36
<800 Ω >2.9 kΩ 37
R1.5 +_ 0.5 38
130BB778.10 39
130BB902.10 40
130BB903.10 40
3.1.4 Decoupling Plate 41
130BB793.10 41
4 How to Order 42
4.1.2 Type Code String 43
4.2.2 Harmonic Filters 45
External RFI Filter 45
5 How to Install 46
5.1.2 Field Mounting 48
5.2 Electrical Data 48
5.2.1 Electrical Overview 48
L1 91 / L2 92 / L3 93 51
U 96 / V 97 / W 98 51
5.2.4 Fuses 51
130BB761.10 53
5.2.6 Control Terminals 54
6 How to Programme 55
56 MG.18.C2.02 - VLT 57
Closed Loop Set-up Wizard 60
Main Menu 62
62 MG.18.C2.02 - VLT 63
7.1.1 Network Connection 65
7.4.7 The PKE Field 68
96 and length 4 would 75
96 and length 75
80 MG.18.C2.02 - VLT 81
8.1 Mains Supply Tables 82
130BB632.10 83
8.2 General Specifications 87
8.3 Acoustic Noise 89
90 MG.18.C2.02 - VLT 91
*MG18C202* 93

Kommentare zu diesen Handbüchern

Keine Kommentare

Danfoss FC 100 Series Spezifikationen Seite 64

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kraftschraubendreher Danfoss FC 100 Series