Danfoss FP715Si Bedienungsanleitung PDF herunterladen (Seite 4)

This product complies with the following EC Directives

Electro-Magnetic Compatibility Directive.

(EMC) (89\336\EEC), (92\31\EEC)

Low Voltage Directive.

(LVD) (73\23\EEC), (93\68\EEC)

Danfoss Randall Ltd

Ampthill Road, Bedford, MK42 9ER

Tel: 01234 364621

Fax: 01234 219705

Email: [email protected]

Website: www.danfoss-randall.co.uk

2 ON/OFFs

PUMPED

7 DAY or 24 HOUR

24 HOUR

3 ON/OFFs

GRAVITY

5/2 DAY

7 DAY

SW.1

SW.2

SW.3

SW.4

Installation Instructions

Product overview

The FP715 is an electronic 2-channel full programmer with independent time

base serving separate heating and hot water channels. It can be set at time of

installation for 7 day, 5/2 day or 24 hour operation. In addition the installer can

select between 2 or 3 sets of On/Off events each day. All models in the range

incorporate a permanently lit back light.

Installation

1. The product should only be installed by a qualified electrician or

competent heating installer. The installation must be in accordance with

the current edition of the IEEE wiring regulations.

2. From the top left hand corner of the wallplate there must be clearances

of at least 140mm to the right, 15mm to the left, 30mm above and 100mm

below in order to mount the plug-on module.

3. The wallplate must be securely mounted either directly to the wall,

using suitable wood screws, or to a flush mounted 1-gang electrical

accessory box using M3.5 screws.

4. Cable access can either be from behind for concealed cabling or from

below for surface cabling. If surface cable is used, cut out cable access

slot on plug-on module prior to mounting the module.

5. For wiring connections refer to Diagram 1 below. FP715 models are

double insulated and do not require an earth connection. However a parking

terminal is provided on the wallplate, which is clearly marked with an Earth

symbol.

6. Prior to mounting the plug-on module, DIL switches on the rear of the

plug-on module must be set. See Diagram 2 below for available options.

7. Mark the INSTALLER SETTING tick box on the inside flap label to

notify user in which mode their unit is set (24hr, 5/2 day or 7 day).

8. Mount plug-on module to wallplate by locating tabs on top of wallplate

in apertures on rear of module, hinge down and press firmly to wallplate

before tightening securing screws on bottom of wallplate.

CP715 FP715 (3028 12/01)

Diagram 1. - Wiring

Diagram 2. - DIL Switch Settings

Fault Check List

Event ON/OFF Mon - Fri * Sat - Sun

1 1st ON 6:30 7:30

2 1st OFF 8:30 10:00

3 2nd ON 12:00 12:00

4 2nd OFF 12:00 12:00

5 3rd ON 17:00 17:00

6 3rd OFF 22:30 22:30

* Each day if set in 24 hour mode

Product specification

Power supply 230 V ac, ±10%, 50/60 Hz

Switching action 2 x SPDT internally linked

Switch rating 230 V ac, 3(1)A

Battery back-up 24 hours minimum

Max. temperature 45°C

Programme resolution 1 minute

Dimensions, mm (W, H, D) 135 x 88 x 32

Design standard EN 60730-2-7

Control Pollution Situation Degree 2

Rated Impulse Voltage 2.5kV

Ball Pressure Test 75°C

Factory Presettings

Part No. 38033 Iss.1 03/03

1 2 3 4

Kommentare zu diesen Handbüchern

Keine Kommentare

Danfoss FP715Si Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Thermostate Danfoss FP715Si