Danfoss TP5000 si range Bedienungsanleitung PDF herunterladen (Seite 1)

Datasheet

TP5000 Si Range

Programmable Room Thermostat

The TP5000 Si is a microprocessor based

programmable room thermostat with many

advanced features. The range includes battery

and 230 volt powered hard-wired models and

battery powered wireless versions. All models

in the range utilise an advanced PI algorithm to

provide close and accurate temperature control to

reduce energy waste and ensure comfort under all

load conditions.

The TP5000 Si incorporates a factory set real time

clock, both date and time are set in the factory to

the appropriate time zone, eliminating the need

to set the time at installation or to change the

time in spring or autumn. This function is powered

from a separate lithium battery which lasts for the

lifetime of the product.

The calendar clock is also used to provide a service

due timer function which can be enabled by the

installer if required. If enabled, several operating

options are available ranging from audible & visual

service due warning to proportional reduction of

heating until the boiler is serviced and the service

due feature is reset by the installer.

The TP5000 Si is a 5-day / 2-day programmable

thermostat which also includes a feature which

allows two blocks of programmes to be set up

(A/B Programming), either programme can then

be assigned to any day of the week allowing the

programming to closer match the lifestyle of the

consumer, all without the need to go for a far

more complex 7-day unit.

Unlike earlier models, the TP5000 Si can be

conﬁ gured by the installer to provide 2, 4 or 6

events per day, it can also be set up to provide

constant temperature control if required, again

this allows the thermostat to be matched with

consumers lifestyle.

Versions with programmable remote inputs are

also available. Remote inputs can be either remote

temperature sensing, (control or limit), or digital

inputs from window contacts, telephone operated

switches, card readers or building automation

systems.

For standard applications the product can be

installed and will work straight out of the box,

however there is a wide range of user and installer

options which allow the product operation to

be tuned to the speciﬁ cation requirements of

the system. Some of these options are hardware

settings made by DIL switches, but the majority

are software settings made in one of two advanced

programming modes.

Settings made by the installer or the end user are

stored for the life of the product in a non-volatile

memory chip which does not require power. This

same storage technique allows customer speciﬁ c

programmes to be established as factory defaults,

but is only available for larger projects.

Signiﬁ cant eﬀ ort has been made to make the

product as energy eﬃ cient as possible, this

includes improving both on/oﬀ performance and

chrono-proportional performance, charts on page

4 detail the relative performance of each mode.

Programming of the TP5000 Si is as simple as it has

always been, just ﬁ ve buttons and an intuitive MMI

ensure that the product is no more complicated to

the user than previous models.

Features

Part No. 082v07 04/09

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Programmable Room Thermostat

1DatasheetTP5000 Si RangeProgrammable Room ThermostatThe TP5000 Si is a microprocessor based programmable room thermostat with many advanced features.

Seite 2 - Installer Hardware Settings

2Datasheet TP5000 Si Programmable Room ThermostatPart No. 082v07 04/09Installer Advanced Programming SettingsOption Description Factory Setting Other

Seite 3 - Datasheet

Datasheet3TP5000 Si Programmable Room ThermostatPart No. 082v07 04/09The service interval timer allows the installer to select a service due date for

Seite 4 - Danfoss Randall Ltd

Datasheet4Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other printed material. Danfoss reserves the right to