Danfoss VLT HVAC Basic Drive FC 101 Spezifikationen PDF herunterladen (Seite 28)

Motor Set-up

The Quick Menu Motor Set-up guides through the needed

motor parameters.

No & Name Range Default Function

0-03 Regional

Settings

[0] Interna-

tional

[1] US

0-06 Grid

Type

[0]-[132] please

see start-up

wizard for

open loop

application

Size selected Select operating

mode for restart

upon

reconnection of

the frequency

converter to

mains voltage

after power

down

1-20 Motor

power

0.12-110 kW/

0.16-150 Hp

Size related Enter motor

power from

nameplate data

1-22 Motor

Voltage

50.0 - 1000.0 V Size related Enter motor

voltage from

nameplate data

1-23 Motor

Frequency

20.0 - 400.0 Hz Size related Enter motor

frequency from

nameplate data

1-24 Motor

Current

0.01 - 10000.00

Size related Enter motor

current from

nameplate data

1-25 Motor

Nominal

Speed

100.0 - 9999.0

RPM

Size related Enter motor

nominal speed

from nameplate

data

4-12 Motor

Speed Low

Limit [Hz]

0.0 - 400 Hz 0.0 Hz Enter the

minimum limit

for low speed

4-14 Motor

Speed High

Limit [Hz]

0-400 Hz 65 Enter the

maximum limit

for high speed

3-41 Ramp 1

Ramp up Time

0.05 - 3600.0 s Size related Ramp up time

from 0 to rated

motor frequency

1-23 Motor

Frequency

3-42 Ramp 1

Ramp Down

Time

0.05 - 3600.0 s Size related Ramp down time

from rated motor

frequency

1-23 Motor

Frequency to 0

1-73 Flying

Start

[0] Disabled

[1] Enabled

0 Select Enable to

enable the

frequency

converter to

catch a spinning

motor

Changes Made

Changes Made lists all parameters changed since factory

setting. Only the changed parameters in current edit-setup

are listed in changes made.

If the parameters value is changed back to factory setting's

value from another different value, the parameter will NOT

be listed in Changes Made.

1. Press [Menu] key to enter the Quick Menu until

indicator in display is placed above Quick Menu.

Press [

▲

] [

▼

] to select either FC101 wizard, closed

loop setup, motor setup or changes made, then

press [OK].

Press [

▲

] [

▼

] to browse through the parameters

in the Quick Menu.

4. Press [OK] to select a parameter.

Press [

▲

] [

▼

] to change the value of a parameter

setting.

6. Press [OK] to accept the change.

7. Press either [Back] twice to enter “Status”, or

press [Menu] once to enter “Main Menu”.

The Main Menu accesses all parameters.

1. Press [Menu] key until indicator in display is

placed above “Main Menu”.

Use [

▲

] [

▼

] to browse through the parameter

groups.

3. Press [OK] to select a parameter group.

Use [

▲

] [

▼

] to browse through the parameters in

the specific group.

5. Press [OK] to select the parameter.

Use [

▲

] [

▼

] to set/change the parameter value.

Quick Guide VLT HVAC Basic Drive Quick Guide

MG18A302 - VLT

is a registered Danfoss trademark 27

1 1

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 45 46

Kommentare zu diesen Handbüchern

Keine Kommentare

Danfoss VLT HVAC Basic Drive FC 101 Spezifikationen Seite 28

Kommentare zu diesen Handbüchern